LOAD INVALID CARD - xxx •.• xxx INV was specified with LOAD and an invalid statement was found.
The message and the contents of the invalid statement (xxx ••• xxx) are listed in the file LOAD MAP. The invalid statement is ignored
and loading continues. DMSLGT002I FILE 'fn NOT FOUND RC=O DMSLI0001E NO FILENAME SPECIFIED RC=24 DMSLI0003E INVALID OPTION 'option' RC=24 DMSLI0005E NO 'option' SPECIFIED RC=24 DMSLI0021E ENTRY POINT 'name' NOT FOUND RC=40 DMSLI0029E INVALID PARAMETER 'parameter' IN THE OPTIJN 'option' FIELD DMSLI0055E NO ENTRY POINT DEFINED RC=40 DMSLI0056E FILE 'fn ft' CONTAINS INVALID [NAMEIALIASIENTRYIESD] RECORD FORMA'TS RC=32 DMSLI0099E CMS/DOS ENVIRONMENT ACTIVE RC=40 DMSLI0104S ERROR Inn' READING FILE 'fn ft fm' FROM DISK RC=100 DMSLI0105S ERROP. Inn' WRITING FILE 'fn ft fm' ON DISK RC=100 DMSLI0109S VIRTUAL STORAGE CAPACITY EXCEEDED RC=104 DMSLI0116S LOADER TABLE OVERFLOW RC=104 DMSLI0168S PSEUDO REGISTER TABLE OVERFLOW RC=104 DMSLI0159S ESDID TABLE OV9RFLOW DMSLI0201W THE FOLLOWING NAMES ARE UNDEFINED: RC=4 DMSLI0202W DUPLICATE IDENTIFIER 'identifier' RC=4 DMSLI0203W "SET LOCATION COUNTER" NAME 'name' UNDEFINED RC=4 DMSLI0206W PSEUDO REGISTER ALIGNMENT ERROR RC=4 DMSLIOQ07T I/O ERROR ON FILE 'fn ft fm' RC=256 DMSSTT062E INVALID * IN FILEID RC=20 128 IBM VM/370 Command and Macro Reference
LOADMOD LOADMOD Use the LOADMOD command to load a MODULE file into storage. The file
must be in nonrelocatable format as created by the command. The
format of the LOADMOD command is: .-- , I LOADMod I L
fn is the filename of the file to be loaded into storage.
filetvpe must be MODULE. The
fm is the filemode of the module to be loaded. If not specified, or
specified as an asterisk, all your disks are searched for the file. 1. You can use the LOADMOD command when you want to debug a CMS MODULE file. After the file is loaded, you may set address stops or
breakpoints before you begin execution with the START command; for
example:
loadmod prog 1
cp adstop 210ae start 2. If a MODULE file was created using the DOS option of the GENMOD command, the CMS/DOS environment must be active when it is loaded.
If it was created using the OS option (the default), the CMS/DOS environment must not be active when it is loaded.
3. MODULE files created with the ALL option, or with SYSTEM option and loaded into the transient area, may be loaded regardless of whether
the CMS/DOS environment is active. If the LOADMOD command is
called from a the loading is also done regardless of
whether the CMS/DOS environment is active.
None. DMSMJ DOD 1 E DM SMO DOO 2E DMSt'!OD032E DMSMOD070E DMSMOD104S DMSMOD109S DMSMOD114E DMSMOD116S DMSSTT048E NO FILENAME SPECIFIED FILE 'fn ft' NOT FOUND INVALID FILETYPE 'ft'
RC=24
RC=28
RC=24 INVALID PARAMETER 'parameter' RC=24 ERROP 'nnw READING FILE 'fn ft fm' FROM DISK VIRTUAL STORAGE CAPACITY EXCEEDED RC=104 'fn ft fm' NOT LOADED; CMS/DOS ENVIRONMENT RC=40 or RC=-0005 LOADER TABLE OVERFLOW RC=104 INVALID MODE 'mode' RC=24 RC=100 [NOT] ACTIVE Section 2. eMS :ommands 129
Previous Page Next Page