t'Clyt:: V.L U\...L;V- lOV ,- IV vpucn:t:!u I, I!lO I DY TNL I Starter Systems
In the followinq example, the responses (format, 131, device type, 000, end cylinder, and VMRELn) format the real disk at address 131 and
label it VMRELn. The label you specify must match what you specified in
the SYSVOL operand of the SYSRES macro statement when you defined the
system in your DMKSYS module. In any case, do not use CPRnLO because
that is the label of the starter system disk. The console output looks
like: VM/370 FORMAT/ALLOCATE PROGRAM RELEASE n
ENTER FORMAT OR ALLOCATE:format
FORMAT FUNCTION SELECTED ENTER DEVICE ADDRESS (CCU):131 ENTER DEVICE TYPE:device type
1
ENTER START CYLINDER (XXX) OR "LABEL":OOO ENTER END CYLINDER (XXX) :end cylinder
1
ENTER DEVICE LABEL:VMRELn2 FORMAT STARTED FORMAT DONE 000 NO. PAGE RECORDS WITH READ-CHECK ERRORS the cperation completes, the prompting massage ENTER FORMAT OR ALLOCATE:
is displayed. Now that the system residence volume is formatted and
labeled, you must allocate the disk space. Again, you must respond to
the promptinq messages. In the following example, the space on the
various device types at address 131, with the label VMRELn, are
indicated. You can use the formulas given in the "Creating Your VM/370 Directory" section of Part 2 to ensure enough space is allocated for
your VH/370 directory. If you do not allocate your DASD space as shown
in this example, you are responsible for ensuring that you have enough TDSK space to perform the assemblies associated with VM/370 system
generation.
ENTER FORMAT OR ALLOCATE:allocate
ALLOCATE FUNCTION SELECTED
ENTER DEVICE ADDRESS (CCU):131 ENTER DEVICE TYPE:device type
ENTER DEVICE LABEL:VMRELn ENTER ALLOCATION DATA FOR VOLUME VMRELn TYPE CYL CYL ... . .. 111! 33.JQ 3340 perm 000 019 000 012 000 023 000 008 drct 020 023 013 016 024 027 009 012 temp 024 100 017 201 028 173 013 276
perm 101 102 202 202 174 176 277 277
temp 103 180 203 389 177 310 278 399
tdsk 181 202 390 402 311 346 400 554
perm3 403 807 347 697
end
1The specifiable device types and their respective "end 2314 is 202, 2319 is 202, 3330 is 403, 3330-11 is 807, 3340-70 is 697, 3350 is 554, 2305-1 is 47 and 2305-2 is 2VMRELn must be VMREL4, VMREL5, or VMREL6, depending
level of the VM/370 SCP. cylinders" are: 3340-35 is 347,
95.
on the release
3This line gives the required specifications for the 3330 the 3340 Model 70. 230 IBM VM/370 Planning and System Generation Guide
Model 11 and
starter Systems ALLOCATION RESULTS l.Jll 3330 J140 112Q PERM 000 019 000 012 000 023 000 008 DRCT 020 023 013 016 024 021 009 012 TEMP 024 100 011 201 028 113 013 216 PERM 101 102 202 202 114 176 277 217 TEMP 103 180 203 389 111 310 218
399 __ TDSK 181 202 390 402 311 346 400 554 PERM 403 807 347 697 DEVICE 131 VOLUME VMRELn ALLOCATION ENDED
ENTER FORMAT OR ALLOCATE: Step 3. Label the Starter System Volume Use the Format/Allocate program to label the scratch volume that is to
contain the CP starter system. This label must be CPRnLO. You can
format and label this volume, or just label it. Formatting is
unnecessary (unless the pack has never been initialized before) because
you are going to restore the starter system to this volume. If you get
an I/O error trying to label the pack, format only cylinder zero and
then try to label the pack again. In the following example, the
responses (format, 130, device type, label, and CPRnLO) to the prompting
messages put the label CPRnLO on the real disk at address 130. ENTER FORMAT OR ALLOCATE: format FORMAT FUNCTION SELECTED
ENTER DEVICE ADDRESS (CCU):130 ENTER DEVICE TYPE:device type
ENTER START CYLINDER (XXX) OR "LABEL": label
ENTER DEVICE LABEL: CPRnLO LABEL IS NOW CPRnLO - When the Format/Allocate program is complete, it responds:
ENTER FORMAT OR ALLOCATE: You need not respond to this message. Press the PAl key twice to return
to CP mode.
Now the starter system volume is available and ready for the data
that is to be placed on it by the DASD Dump Restore service program
(module DMKDDR). The DASD Dump Restore program is the second file on the
starter system tape. Step 4. Load the DASD Dump Restore Program from
the Starter System Tape IPL the starter system tape a second time to load the DASD Dump Restore
(DDR) program. It is the second file on the starter system tape. Do
not rewind the tape, because the next file is needed in Step 5. Step 5. Restore the Starter System to Disk
Respond to the DDR prompting messages to restore the starter system.
Part 3. Generating VM/370 (CP, CMS, RSCS, and IPCS) 231
Previous Page Next Page