VMSERV OPTION CONFLICT EXISTS. PLEASE RE-ENTER
Return code: 4 Issued for conflicting parameters issued on the command line: Such
as 'BUILD' and 'NOIPL'. You should review the PUT DOCUMENT and
re-enter the command properly. UNKNOWN OR INCOMPLETE OPTION SPECIFIED. PLEASE RE-ENTER
Return code: 4 You have invoked VMSERV with misspelled or incorrect parameters. You must re-enter the command correctly.
THE SECOND PARAMETER ENTERED MUST BE THE PROGRAM NUMBER AT WHICH YOU WISH SERVICE INSTALLATION TO 'RESTART'. ENTER: VMSERV RESTART
prog
Return code: 4 You have requested a 'RESTART' but have not indicated which service EXEC you wish to restart.
ENTER THE PROGRAM NUMBER YOU WISH TO BUILD OR 'EXIT'. Return code: none -no exit You have requested 'BUILD' but specified no progid to invoke. You should respond with the program number you wish to 'BUILD', or you
may enter 'EXIT' to terminate VMSERV. progid EXEC NOT FOUND. RE-ENTER IF TYPING ERROR. OR ENTER 'EXIT' IF YOU NEED TO RE-START.
Return code: none -no exit You have incorrectly specified the progid to 'BUILD'. You may
re-enter the progid or enter 'EXIT' to terminate VMSERV. VMSERV WILL NOW MAP THE PUT. PROCESS WILL TAKE A FEW MINUTES Return code: none -informational
Followed by the typing of the first line of the 'program level'
files as they are read from the PUT. This file contains the
official name of that particular (program) product. YOU SHOULD REVIEW THE KEMOS-TO-USERS PRIOR TO INSTALLING SERVICE WOULD YOU LIKE THE 'MEMO (S)-TO-USERS' PRINTED? ( -YES- , NO )
Return code: none -procedural question 396 IBM VM/370 Planning and System Generation Guide

VMSERV Issued if the PUT was just mapped. It may be the initial
invocation of VMSERV, or a 'RESTART' where no 'SERVICE DISKMAP' file was found on the 'C' disk. INSURE (VIA THE MEMO-TO-USERS) THAT NO CHANGES HAVE OCCURRED TO THE MACROS AFFECTING DMKRIO, DMKSNT, and DMKSYS. IF THESE, OR ANY MODULE(S) NEED TO BE RE-ASSEMBLED FOR MACRO OR OTHER CHANGES, OR IF YOU WISH TO RECEIVE CONTROL AFTER THE MACLIBS AND OTHER SERVICE IS LOADED, USE THE 'NOIPL' OPTION WHEN YOU RE-INVOKE VMSERV TO INITIATE THE APPLICATION OF SERVICE. THE MEMO-TO-USERS SHOULD BE REVIEWED PRIOR TO INSTALLING SERVICE WHEN YOU HAVE REVIEWED THE MEMOS AND ARE READY TO APPLY SERVICE, ENTER... VMSERV NOMEMO (USE THE 'NOIPL' OPTION IF NECESSARY) Return code: 0 - normal termination
Issued a fter the printing of the MEPIOs (if requested) to remind you
about the 'NOIPL' option and to let you know that VPISERV is about
to terminate and how you may restart. SERVICE APPLICATION MESSAGES YOU WILL BE REQUIRED TO REPLY TO QUESTIONS REGARDING THE APPLICATION OF SERVICE. THE ACCEPTABLE RESPONSES WILL BE SHOWN IN PARENTHESES. A RESPONSE SHOWN WITHIN DASHES: -yes-, IS THE DEFAULT, AND MAY BE SELECTED WITH A NULL RESPONSE. Return code: none -informational message MOUNT THE VPI/370 SYSTEM PUT ON 181 AND RE-ISSUE VMSERV Return code: q A 'CP REW 181' has resulted in an error. Perhaps the tape is is
not attached.
THE TAPE ON YOUR VIRTUAL 181 IS NOT THE CORRECT TAPE. VM/370 SYSTEM PUT ON 181 AND RE-ISSUE VMSERV Return code: q MOUNT THE
The initial 'VMFPLC2' command has resulted in a tape error.
probably the wrong tape was mounted. THIS SERVICE PROCEDURE NEEDS AN 'AI DISK TEMPORARILY ON WHICH TO WRITE 2 SMALL FILES. ENTER THE 'CUU' OF A DISK THAT MAY BE ACCESSED BY THE PROCEDURE. (-194- I CUU )
Return code: none -procedural question
Enter an address of a minidisk to which you now have write access.
If there is a problem, the message will be reissued. Part 5. Updating VM/370 397