Figure 183: MAINSIZE command (Set size of locked main storage) ....................................................... 436 Figure 184: MANUFACTURER command (set STSI manufacturer code) ............................................... 437 Figure 185: MAXCPU command (display current number of installed processors) ................................. 439 Figure 186: MAXCPU command (set number of installed processors) ................................................... 439 Figure 187: MAXRATES command (set the interval time) ....................................................................... 441 Figure 188: MAXRATES command (display maximum rates) ................................................................. 441 Figure 189: MEMLOCK command ........................................................................................................... 442 Figure 190: MESSAGE command ............................................................................................................ 443 Figure 191: MODEL command (set STSI model name, variant 1)........................................................... 445 Figure 192: MODEL command (set STSI model name, variant 2)........................................................... 445 Figure 193: MODEL command (set STSI model name, variant 1)........................................................... 445 Figure 194: MODPATH command (display dynamic load module path) ................................................. 446 Figure 195: MODPATH command (set dynamic load module path) ........................................................ 447 Figure 196: MOUNTED_TAPE_REINIT command (display settings). ..................................................... 449 Figure 197: MOUNTED_TAPE_REINIT command (disable tape mount reinitialization) ......................... 449 Figure 198: MSG command ..................................................................................................................... 450 Figure 199: MSGHLD command (set new interval) ................................................................................. 451 Figure 200: MSGHLD command (release messages) ............................................................................. 452 Figure 201: MSGLEVEL command (display message level) ................................................................... 455 Figure 202: MSGLEVEL command (suppress certain messages)........................................................... 455 Figure 203: MSGLEVEL command (set message level DEBUG) ............................................................ 455 Figure 204: MSGNOH command ............................................................................................................. 457 Figure 205: MT command (REW operation) ............................................................................................ 460 Figure 206: MT command (ASF operation) .............................................................................................. 460 Figure 207: MT command (FSF operation) .............................................................................................. 460 Figure 208: MT command (FSR operation) .............................................................................................. 460 Figure 209: MT command (WTM operation) ............................................................................................ 461 Figure 210: MT command (DSE operation) ............................................................................................. 461 Figure 211: NUMCPU command (display current number of emulated CPUs) ....................................... 463 Figure 212: NUMCPU command (increase emulated CPUs) .................................................................. 463 Figure 213: NUMCPU command (reduce emulated CPUs) ..................................................................... 463 Figure 214: NUMVEC command (display current number of vector facilities) ......................................... 464 Figure 215: NUMVEC command (set number of vector facilities) ............................................................ 464 Figure 216: OSTAILOR command (display intended operating system) ................................................. 466 Figure 217: OSTAILOR command (specify intended operating system) ................................................. 466 Figure 218: OSTAILOR command (combine intended operating systems) ............................................. 466 Figure 219: OSTAILOR command (combine intended operating systems) ............................................. 467 Figure 220: PANRATE command (list current panel refresh rate) ........................................................... 468 Figure 221: PANRATE command (set new panel refresh rate) ............................................................... 469 Figure 222: PANTITLE command (set a new console window title) ........................................................ 471 Figure 223: PANTITLE command (remove console window title)............................................................ 471 Figure 224: PGMPRDOS command ........................................................................................................ 472 Figure 225: PGMTRACE command (display settings) ............................................................................. 473 Figure 226: PGMTRACE command (change settings) ............................................................................ 474 Figure 227: PLANT command (set STSI plant name) .............................................................................. 475 Figure 228: PR command......................................................................................................................... 476
Figure 229: PSW command (display PSW). ............................................................................................ 479 Figure 230: PSW command (modify condition code) ............................................................................... 480 Figure 231: PSW command (modify condition code and addressing mode) ........................................... 480 Figure 232: PTP command (enable debug tracing) ................................................................................. 482 Figure 233: PTP command (disable debug tracing) ................................................................................. 482 Figure 234: PTT command (display trace options / set options and start trace) ...................................... 485 Figure 235: PTT command (display trace entries) ................................................................................... 486 Figure 236: PTT command (start trace and issue automatic display) ...................................................... 487 Figure 237: PWD command ..................................................................................................................... 488 Figure 238: QCPUID command ............................................................................................................... 489 Figure 239: QD command ........................................................................................................................ 491 Figure 240: QPFKEYS command ............................................................................................................ 494 Figure 241: QPID command ..................................................................................................................... 495 Figure 242: QPORTS command .............................................................................................................. 496 Figure 243: QPROC command ................................................................................................................ 497 Figure 244: QSTOR command ................................................................................................................. 498 Figure 245: QUIET command .................................................................................................................. 499 Figure 246: QUIT command ..................................................................................................................... 501 Figure 247: QUIT FORCE command ....................................................................................................... 501 Figure 248: QUITMOUT command .......................................................................................................... 502 Figure 249: R command (display real storage) ........................................................................................ 504 Figure 250: R command (alter real storage) ............................................................................................ 504 Figure 251: RESTART command ............................................................................................................. 505 Figure 252: RESUME command .............................................................................................................. 507 Figure 253: REXX command (display interpreter settings) ...................................................................... 512 Figure 254: REXX command (set PATH) ................................................................................................. 512 Figure 255: REXX command (set EXTENSION)...................................................................................... 513 Figure 256: REXX command (set ERRPREF) ......................................................................................... 513 Figure 257: REXX command (disable ERRPREF)................................................................................... 513 Figure 258: REXX command (RESOLVER ON) ...................................................................................... 514 Figure 259: REXX command (RESOLVER OFF) .................................................................................... 514 Figure 260: RMMOD command ............................................................................................................... 515 Figure 261: S command (address range) ................................................................................................. 517 Figure 262: S command (address with length)......................................................................................... 517 Figure 263: S command (all addresses) .................................................................................................. 517 Figure 264: S+ command ......................................................................................................................... 519 Figure 265: S- command .......................................................................................................................... 520 Figure 266: S? command ......................................................................................................................... 521 Figure 267: S+ dev command .................................................................................................................. 523 Figure 268: S- dev command ................................................................................................................... 523 Figure 269: SAVECORE command (save specific area) ......................................................................... 525 Figure 270: SAVECORE command (save from begin to end) ................................................................. 525 Figure 271: SCLPROOT command (display SCLP base directory) ......................................................... 526 Figure 272: SCLPROOT command (set SCLP base directory) ............................................................... 527 Figure 273: SCP command ...................................................................................................................... 528 Figure 274: SCPECHO command ............................................................................................................ 529
Previous Page Next Page