October 1, 1979 PROBLEMS AND MESSAGES
MESSAGES
FINI
(FU) FULLPRINT was completed successfully.
FINIS
(OT) OTYPE was completed and has been sent to the virtual
printer.
FMAC: <file> COPY NOT FOUND
Respecify.
FMAC: ERROR IN LINE <n>
Only the characters "&", "C", "I", "R" or a digit from "1" to
"9" are valid when preceded by an ampersand. This message is
also caused if there is a bad character in the MEMO file or if
an error occurs while reading the MEMO file.
FMAC: ERROR WHILE READING <file> MEMO
Contact the FRESS staff.
FMAC: ERROR WHILE WRITING TO <file> COPY
Try again.
FMAC: FATAL MACLIB ADD ERROR <n>
If respecifying does not work, contact the FRESS staff.
FMAC: FATAL MACLIB COMP ERROR <n>
If respecifying does not work, contact the FRESS staff.
FMAC: FATAL MACLIB DEL ERROR <n>
If respecifying does not work, contact the FRESS staff.
FMAC: FATAL MACLIB ERROR <n>
If respecifying does not work, contact the FRESS staff.
FMAC: FATAL MACLIB GEN ERROR
<maclib> did not exist and is being created.
FMAC: FATAL MACLIB LIST ERROR <n>
If respecifying does not work, contact the FRESS staff.
FMAC: FMACCVTC ERROR <n> ON <macname> MEMO
If respecifying does not work, contact the FRESS staff.
FMAC: FMACCVTM ERROR <n> ON <macname> COPY
If respecifying does not work, contact the FRESS staff.
FMAC: INVALID CHAR AFTER & IN <file> MEMO
Only the characters "&", "C", "I", "R" or a digit from "1" to
"9" are valid if preceded by an ampersand. This message is
also caused if there is a bad character in the MEMO file or if
an error occurs while reading the MEMO file.
FRESS Resource Manual Release 9.1 FRESS RSection E.3 -- 283
October 1, 1979 PROBLEMS AND MESSAGES
MESSAGES
FMAC: LMEMBERS ERROR <n>
If respecifying does not work, contact the FRESS staff.
FMAC: MACLIB NOT FOUND ON A-DISK
The specified macro library could not be updated because it is
not on a read/write A-disk.
FMAC: <file> MEMO CONTAINS CHARS WHICH ARE NOT ALLOWED
Only the characters "&", "C", "I", "R" or a digit from "1" to
"9" are valid if preceded by an ampersand. This message is
also caused if there is a bad character in the MEMO file or if
an error occurs while reading the MEMO file.
FMAC: <file> MEMO NOT FIXED LENGTH 80
The logical record length of the MEMO file must be 80.
Specify "LRECL 80" while in the Editor.
FMAC: <macname> MEMO NOT FOUND
The specified macro does not exist as a MEMO file. Execution
of the FMACADD continues for the other macros.
FMAC: MORE THAN 10 MACROS TYPED; FIRST 10 USED
The limit of 10 <macname>s has been exceeded. All but the
first 10 have been ignored.
FMAC: NO MACLIB TYPED
No <libname> was specified.
FMAC: NO MACROS TYPED
No <macname>s were specified.
FMAC: <macname> NOT FOUND
The specified macro was not found in the specified macro
library.
FMAC: ONE OR MORE MACROS NOT IN MACLIB; NOTHING DONE
One of the specified <macname>s is not in the specified
library. The command has been ignored.
FMAC: ONE OR MORE MEMO FILES NOT FOUND
Nothing was done.
FOOTNOTE(S) TOO LONG
(FU) The file specified a footnote longer than a full page,
which cannot be properly formatted. FULLPRINT terminated at
Note the point where the error occurred. ____: this message only
appears during FULLPRINT, not while the file is being edited.
FRESS
The user is [back] in Command Mode.
284 -- Section E Release 9.1 FRESS Resource Manual
Previous Page Next Page